Back to Contents Page

System Overview: Dell™ PowerEdge™ 350 Systems Service Manual

Overview Service Features
System Features Technical Specifications

Overview

The Dell PowerEdge 350 system uses an Intel® Celeron® or Pentium® III microprocessor and next-generation chip set and memory technology to provide high performance in Internet server and Web hosting application environments.

This section describes the hardware features that simplify servicing of the system. It also describes major hardware and software features of the system.

warn.gif (1119 bytes) NOTE: The PowerEdge 350 system is a "headless" system that operates without keyboard, monitor, or mouse. While it is possible to connect these peripherals to the system, it is generally not necessary unless troubleshooting the system.

System Features

The system offers the following major features:

 

The system board includes the following features:

The following software is included in the system:


Service Features

The system includes a diagnostics CD, which checks for hardware problems (if the system can boot). The diagnostics utility makes troubleshooting and repair easy and effective, in most cases without tools or service aids. For information on using the system diagnostics, see "Basic Troubleshooting."

If you have hard-disk drive problems, use the information in "Basic Troubleshooting" to back up the hard-disk drives, and then reinstall the system software.

The system chassis simplifies removing and replacing components. You can replace the microprocessor or memory modules without removing the system board.


Technical Specifications

There are two optional processors. Your system has one processor.

Microprocessor

Microprocessor type Intel Celeron  microprocessor with an internal operating frequency of at least 600 MHz and an external operating frequency of 66 MHz
Front side bus 66 MHz
Internal L2 cache 128 KB, internal to microprocessor
Math coprocessor internal to microprocessor

or

Microprocessor

Microprocessor type Intel Pentium III microprocessor with an internal operating frequency of at least 750 MHz and an external operating frequency of 100 MHz
Front side bus 100 MHz
Internal L2 cache 256 KB, internal to microprocessor
Math coprocessor internal to microprocessor

 


Expansion Bus

Bus type PCI bus
Expansion slots one full-length PCI slot; one low-profile PCI slot (occupied by video controller)



Memory

DIMM sockets four 72-bit wide, 168-pin sockets
DIMM capacities 128-, or 256-MB unbuffered and registered SDRAM DIMMs; must be rated for 100-MHz operation
Minimum RAM 128 MB
Maximum RAM 1 GB
External cache none

Drives

Diskette drive 3.5-inch, 1.44 MB diskette drive included with standard system
Hard-disk drives two 1-inch high ATA-100 IDE slots in hard-disk drive bay support formatted capacities from 10 GB to 20 GB and higher
CD-ROM drive IDE

External Ports and Connectors

Serial   two 9-pin connectors
Video 15-pin connector
PS/2-style keyboard 6-pin mini-DIN connector
PS/2-compatible mouse 6-pin mini-DIN connector
USB two USB-compliant 4-pin connectors
Ethernet two RJ45 connectors for connection to integrated Intel 82559 10/100 Ethernet controllers



Video

Video type PCI video controller; VGA connector
Video memory 8-MB SDRAM standard (not upgradable)

Power

DC power supply:
Wattage 125 W
Heat dissipation 898 BTU/hr (maximum)
Input voltage 100 to 120 V at 50 Hz/200 to 240 V at 60 Hz
autoranging, power factor corrected
Output voltages
and maximum
current



Max. inrush current
+5 VDC at 13 A
+3.3 VDC at 6 A
+12 VDC at 3 A
–12 VDC at 0.2 A
+5 Vfp (volts flea power) at 1 A

Under typical line conditions and over the entire system ambient operating range, the inrush may reach 140 A for the installed power supply.
Backup battery 3-V CR2032 lithium coin cell



Physical

Rack mount (1U):
Height 4.3 cm (1.7 inches)
Width 42.5 cm (16.7 inches)
Depth 55.8 cm (22 inches)
Weight 10 kg (23 lb) maximum configuration



Environmental

Temperature:

    Operating

10°C to 35°C (50°F to 95°F) derated 0.5°C per 1000 ft

    Non-operating

–40°C to 65°C (–40°F to 149°F)

    Maximum
    gradient


10°C per hour maximum rate of change
Relative humidity:
     Non-operating 5% to 95% (noncondensing) at 30°C
Maximum shock:
    Operating six consecutively executed shock pulses in the positive and negative x, y, and z axes (one pulse on each side of the system) of 41 G for up to 2 ms
    Package six consecutively executed shock pulses in the positive and negative x, y, and z axes (one pulse on each side of the system) of 71 G for 2 ms
Altitude:
    Operating –16 to 3048 m (–50 to 10,000 ft)
High-potential ESD:
    Electrostatic
    discharge

15kV
Noise (maximum):
    Acoustic noise < 45dbA @ 23°C ±2°C

Back to Contents Page