 |
FECO: | COMMS # 31/1 |
| MODIFICATION No: | N/A | |
| PRODUCT: | RACAL MAXAM MXF MODEM | |
| SUB-ASSEMBLY | N/A | |
| ESTIMATED MAN HOURS | N/A | |
| CLASS OF CHANGE: | INFORMATIONAL | |
| REASON FOR CHANGE: | TO INTRODUCE THE MAXAM MXF RANGE OF MODEMS |
FECO COMMS # 31/1
|
FECO: | COMMS # 31/1 |
| MODIFICATION No: | N/A | |
| PRODUCT: | RACAL MAXAM MXF MODEM | |
| SUB-ASSEMBLY | N/A | |
| ESTIMATED MAN HOURS | N/A | |
| CLASS OF CHANGE: | INFORMATIONAL | |
| REASON FOR CHANGE: | TO INTRODUCE THE MAXAM MXF RANGE OF MODEMS |
1.The racal maxam mxf range of modems are used as dial up diagnostic support modems.
2.They are powered from an external power supply that is unique to the mxf range and
must not be used on any
other of the maxam range.
3.The mxf range and mec descriptions are listed below.
2400 v22 rac-mxf2422-modem(v22)
9600 v32 rac-mxf9632-modem(v32)
14.4 v32 rac-mxf1432-modem(v32)
4.The mxf front and rear panels are shown below.
(tech serv ref: 22/1/5)
5.Features
The sloping fronted beige modem measures approx:
15.5 x 26 x 3.5mm
6 x 10 x 1.5inches
6.Internal switches and jumpers
There is no need to access the interior as there are no internal switches or jumpers.
7.External switches and indicators
7.1.front panel indicators
Pwr
Tx
Rx
Fax
Data
Orig
Ans
Lt
Dcd
Oh
Dtr
7.2.front panel switches
Ans/orig
Dial
Test
Reset
8.At power on the modem will sequence up leaving the pwr lt/dcd and dtr lamps on.
9.Configuration dial up
9.1.connect a vdu to the dte port.
Enter ati3response is display of model no and firmware revision.
9.2.other initial options
Enter ati0display product id code.
Enter ati1display firmware code.
Enter ati5displays product features.
Enter ati8displays country code.
Enter at&vdisplays active and stored profile.
9.3.enter at&vto display and note settings.
9.4.enter at&fto reload factory default.
9.5.enter at&u2&k3so=1s31=ofn&w0w1
Where &u2enables pass through xon/xoff.
&k3enables xon/xoff modem flow control.
So=1enable auto answer on 1 ring.
S31=0terminal speed lock - auto detect.
&wsaves settings.
Fnselect speed as per below.
9.6.note:when the modem is connected to a power stack system, it needs to be in the quiet mode. Also enter:-
Atq1&w0&w1.
9.7.dialback setup.
9.7.1commands:-
At\bsdialback setup
At\bvview dialback setup
At\b1enable dialback
At&w0&w1save settings
Note: these setups are case sensitive.
9.7.2there can be upto 20 users, numbered 1-20.
In addition there is a master user, user 0.
9.7.3.to enable dialback
Enter at\b1&w0&w1
9.7.4to view existing setup
Enterat\bv
Then use factory default or edp setting, which ever is set.
Factory defaultedp setting
At user id prompt enter passwordsetup
At password prompt enter passwordmaxam4
The existing setup will be displayed, excluding user 0.
9.7.5edp standard set up
Setup the following user id's; and any customer requirements.
User id number user idpasswordtelephone number
0setupmaxam4
2bmlb77871301737 778713
4bmld77984501737 779845
5thrupassthrupass
6bmle4942601606 49426
Note:usually id's 0 and 5 are only used now.
9.7.6to change set up
Enter at\bs
At master user id prompt, enter "password" or "setup" whichever applicable.
At master user password prompt, enter "password" or "maxam4" whichever applicable.
At prompt user number enteruser number
At prompt user id?enternew user id
At prompt dialback password enternew password
At prompt dialback number enternew number
Note:for user 0 and 5 do not enter new number above, just leave blank by pressing, enter.
Repeat the above for all users required.
Finally enter at&w0&w1 to save.