 |
FECO: | MT # 93 |
| MODIFICATION No: | N/A | |
| PRODUCT: | TALLY 2045 / 2060 PRINTER | |
| SUB-ASSEMBLY | N/A | |
| ESTIMATED MAN HOURS | N/A | |
| CLASS OF CHANGE: | INFORMATIONAL | |
| REASON FOR CHANGE: | TO RELEASE THE TALLY 2045 & 2060 PRINTERS. |
FECO MT # 93
|
FECO: | MT # 93 |
| MODIFICATION No: | N/A | |
| PRODUCT: | TALLY 2045 / 2060 PRINTER | |
| SUB-ASSEMBLY | N/A | |
| ESTIMATED MAN HOURS | N/A | |
| CLASS OF CHANGE: | INFORMATIONAL | |
| REASON FOR CHANGE: | TO RELEASE THE TALLY 2045 & 2060 PRINTERS. |
1 Reason for change
EDP introduce the tally 2045 and tally 2060 impact printers. They are 132 column 24 pin printhead heavy duty printers designed for up to 900 pages per day.
They are designed to compete with the OKI 395 or OKI 3410.
The 2060 is a faster version.
(tech serv ref 97/29)
2. Specification
Performancet2045t2060
Dpq @ 20cpi600800
Dpq @ 10cpi450600
Nlq @ 20cpi200266
Lq @ 20cpi200266
Lq @ 10cpi100133
Printhead24pins. Auto gap adjustment
Character pitch5, 6, 7.5, 8.6, 10, 12, 15, 17.1, 20 cpi
Fonts
Standarddpq fast, dpq, courier, roman, sanserif, prestige, script, ocr a + b.
Barcodes19 + lcp
Us - postnet barcode.
Emulationsmtpl
Epsom lq - 2550
Ibm proprinter xl24e
Resolution60 to 360 dpi
Self testascii test
Hexdump
Fault display
Printer buffer 128k
Panellcd display 2 x 16 digit.
6 function keys.
Interface serial - parallel
Noise2045 - 53dba2060 - 55dba
Throughput2045 18000 pages/month
450 pages/hour
2060 22, 400 pages/month
540 pages/hour
Power consumption 85va
Dimensionswidth623mm25.5in
Height275mm11.2in
Depth399mm16.2in
Weight18.5kg37.1 lbs
Service lifeprinthead 400 millions dpq
Ribbon 15 million characters.
Paper handlingcut sheet & single part60-120gsm
With csf60-90gsm
Multi part t2045 1+5t2060 1+6
Top50-60gsm
Copies45-56gsm
Bottom50-60gsm
3. mec identites
2045tally-2045
2060tally-2060
4. Initial installation/ set up
4.1 unpack
4.2 check voltage
4.3 power on
4.4 load ribbon
4.5 load paper, with aga gap is set automatically
4.6 print current settings
4.7 set tear
4.8 set top of form
4.9 set edp standard settings
4.10 print settings
4.11 set any customer settings
4.12 print settings
5. load ribbon
5.1 ensure any paper loaded in the printer is removed
5.2 ensure the power is switched on.
5.3 open the front top cover of the printer
5.4 slide the coloured friction handle to the left, (in the direction of
the arrow) as shown in the figure and lift
the friction mechanism.
5.5 move the print head to approximately the centre.
Beware!! The printhead may be hot if it has been in use.
5.6 remove the used cassette, if applicable
5.7 lift the coloured insertion guide a
5.8 insert the coloured tension knob in to the fromt right receptacle of the new ribbon cassette.
Turn the knob in the direction of the arrow to tighten the ribbon.
5.9 slightly tilt the ribbon cassette towards the front and insert the
ribbon between the coloured insertion guide
and the paper guide (transparent plastic plate).
5.10 align the cassette properly and press down until it clicks into place.
5.11 turn the tension knob in the direction of the arrow to slacken the ribbon until it
touches the ribbon carrier at
the bottom.
5.12 push the coloured insertion guide a down.
5.13 move the print head carriage several times to and fro. The ribbon is inserted
correctly if there is no
resistance.
5.14 press the friction mechanism down until it clicks into place.
5.15 close the front top cover.
6. loading paper
6.1 slide the latches on the front flap upwards, then turn the flap itself upwards until it clicks into place.
6.2 lift the single sheet feeder b.
6.3 open the left and right hand tractor flaps. Turn the coloured levers toward the front to unlock the tractors.
6.4 insert the fanfold paper into the left tractor first. Make sure that at
least three perforated holes are
engaged with tractor pins.
Close the tractor flap
Align the tractor in such a way that the first printing position matches the x mark on the printer housing. Lock the tractor by turning the tractor lever towards the rear.
6.5 align the right hand tractor to the paper width, insert the paper,
close the tractor flap and lock the tractor
by turning the tractor lever towards the rear.
6.6 slightly raise the single sheet feeder to release it then push it inwards and down.
Close the front flap and latch.
6.7 paper is automatically fed when the printer is in online status and received data from the computer.
Press the load key to load paper before printing.
7. menu structure
8. to print current settings
8.1 ensure printer is offline
8.2 press set up
8.3 select menu
8.4 select print
9. set tear position
9.1 press setup
9.2 press adjust
9.3 press tear
9.4 press < or > to move the perforation to the appropriaate position.
9.5 confirm the setting by pressing the set button
9.6 press the set up button, and the printer will return to its initial status.
9.7 the correction shown in 72nds of an inch to a maximum of 1" in both directions.
10. set top of form (tof)
10.1 open the top cover
10.2 the tof can be set for each individual type of paper source and each menu.
Tof should be adjusted after the tear position.
10.3 press set up
10.4 press adjust
10.5 press tof
10.6 the bottom edge of the currently valid first printing line a of the paper is transported to the tear edge b.
The factory setting for the first printing position is 12/72".
10.7 press < or > to move the first printing line to the appropriate position.
You can set values from 0 to 220/72" for fanfold paper or 0 to 72/72" for single sheet.
10.8 confirm the setting by pressing set button.
10.9 press the setup key. The printer returns to its initial status.
11. edp standard settings
Font draft
Cpi10 cpi
Lpi6 lpi
Skip0.0inch
Emulateibm propr.xl24
Bidiron
Cg-tabgraphic
Charsetextended
Countrytable 437
S1.zerooff
Auto-cron
Auto-lfoff
Autotearviewtear=off
Width13.6inch
Barcodeof
Barmodeunsecured
Tractor
Formlenletter 11"
Head18
Formadj12/72"
Bin1
Formlen12.0inch
Head18
Formadj12/72"
Bin2
Formlen12.0inch
Head18
Formadj12/72"
Single
Formlen11.0inch
Head18
Formadj12/72"
12. ribbon mask replacement warning
The ribbon mask is held by different screws on the left and right hand side.
The left one should be m3x6mm and the right one m3x8mm.
If you mix the screws up you can damage the aga sensor.
When replacing the screws ensure that the correct screws is are in the correct position.
13. key presses
Switch on with all four buttons pressed will reset the printer.
14. error messages
Printhead hot
Parity error
Framing error
Hardware alarm
Overrun error
Eject error
Load error
Cover open
Ths error t2060 only
15. test mode
Switch on holding online gives you
Self test mode
Hex dump
Default form length
Aga on or off
Physical adjustment
Paper handling
Line wrapping
Sound on or off
16. interior access
16.1 remove the rear cover
16.2 at the rear release the complete top cover assembly by inserting a small
screwdriver into the two release
holes, approx 2 inches down and 2 inches in
from each side.
16.3 pivot the cover off towards the front.
Beware!! There is a short ribbon cable attached to the front control panel.
16.4 release control panel from the panel. Disconnect the ribbon cable from the control panel.
16.5 remove the serial interface by pulling the coloured lever at the rear, and remove the interface from the side,
16.6 to remove the rear tray assembly
(contains psu, main logic, mains input and mains switch)
16.7 unscrew rear fixing screw.
16.8 withdraw the assembly a little. Beware of mains switch lead.
16.9 release the mains switch by rotating 90 degrees and lifting out.
16.10 the assembly can now be completely withdrawn.
16.11 the assembly is plastic with a metal plate chassis.
The main logic plugs into a connector card to which are the connectors for all the motors/switches/sensors etc.
16.12 the paper assembly is held into the base by four rubber looped bungs.
17. at present edp is only supplying the 2045 not the 2060.